Call (818) 848-3163

Go to…

RAM

Home / RAM

We Service and Repair all RAM cars

  • 2018 RAM 2500 HD

    RAM 2500 HD
    Mileage
    130,898
    Service Date
    5/8/2026
    Services Performed
    • CONFIRMED CHECK ENGINE LIGHT ON WITH STORED EVAP SYSTEM CODES P0456 (EVAP SMALL LEAK DETECTED) AND P0457 (EVAP SYSTEM LEAK DETECTED – FUEL CAP LOOSE/OFF). PERFORMED INITIAL EVAP SYSTEM INSPECTION INCLUDING GAS CAP VERIFICATION, HOSE INSPECTION, AND SMOKE TEST OF EVAP SYSTEM. DURING SMOKE TESTING, A SMALL LEAK CONDITION WAS OBSERVED WITH NO VISIBLE EXTERNAL HOSE DAMAGE OR DISCONNECTION FOUND. PERFORMED ACTIVATION AND COMMAND TESTING OF EVAP PURGE VALVE AND FOUND VALVE NOT PROPERLY SEALING WHEN DE-ACTIVATED, ALLOWING UNCONTROLLED VAPOR FLOW. THIS CONDITION INDICATES INTERNAL FAILURE OF PURGE VALVE. ADDITIONALLY, PERFORMED FUNCTION TESTING OF LEAK DETECTION PUMP (LDP) AND FOUND UNIT NOT HOLDING OR BUILDING PROPER VACUUM/PRESSURE DURING EVAP MONITOR TESTING. DATA SHOWED INCONSISTENT PRESSURE READINGS AND FAILURE TO COMPLETE EVAP SYSTEM SELF-TEST, INDICATING FAULTY LEAK DETECTION PUMP OPERATION. BASED ON TESTING AND OBSERVED RESULTS, THE EVAP SMALL LEAK CONDITION IS CAUSED BY A COMBINATION OF A DEFECTIVE PURGE VALVE AND A FAULTY LEAK DETECTION PUMP, RESULTING IN FAILURE OF THE EVAP SYSTEM TO PROPERLY SEAL AND PASS MONITORING TESTS. RECOMMEND REMOVE AND REPLACE PURGE VALVE AND LEAK DETECTION PUMP, FOLLOWED BY EVAP SYSTEM VERIFICATION TEST. – Customer acknowledged notice and gave oral approval of estimated repairs. REMOVE AND REPLACE EVAP PURGE VALVE IN ENGINE BAY AND LEAK DETECTION PUMP LOCATED UNDER VEHICLE NEAR CHARCOAL CANISTER. REMOVED FAULTY COMPONENTS, INSTALLED NEW PURGE VALVE AND LEAK DETECTION PUMP, AND VERIFIED ALL ELECTRICAL CONNECTIONS AND VACUUM LINES ARE SECURE AND PROPERLY ROUTED. CLEARED EVAP SYSTEM CODES AND PERFORMED FUNCTION TEST/VERIFICATION. SYSTEM OPERATING PROPERLY AT THIS TIME WITH NO LEAKS PRESENT.
     
    TOM H. gave our service a 5 star review on 5/9/2026

  • 2018 RAM 2500 HD

    RAM 2500 HD
    Mileage
    130,328
    Service Date
    3/27/2026
    Services Performed
    • PERFORMED DIAGNOSTIC INSPECTION OF A/C AND BLOWER MOTOR SYSTEM. HOCKED UP A/C MACHINE AND CHECK A/C SYSTEM IT IS LOW PRESSURE BUT IS NOT THE REASON FOR NOT WORKING. THEN WE FOUND BLOWER MOTOR NOT OPERATING. CHECKED RELATED FUSES AND RELAYS AND FOUND 40 AMP FUSE TO BE BLOWN. REPLACED FUSE; HOWEVER, BLOWER MOTOR STILL NOT RECEIVING POWER. PERFORMED FURTHER ELECTRICAL TESTING AND TRACED CIRCUIT FROM FUSE BOX TO BLOWER MOTOR. FOUND OPEN CIRCUIT/FAULT IN WIRING BETWEEN FUSE BOX AND BLOWER MOTOR. RECOMMEND LOCATING EXACT POINT OF BREAK AND REPAIRING OR REPLACING DAMAGED WIRING AS NEEDED.
     
    TOM H. gave our service a 5 star review on 3/28/2026

  • 2016 RAM ProMaster 1500

    RAM ProMaster 1500
    Mileage
    93,916
    Service Date
    6/15/2023
    Services Performed
    • Connected a scan tool and found code P0520 – Engine Oil Pressure Sensor/Switch Circuit. Performed an inspection of the engine oil level and condition and found it was at the proper level and clean. Performed a visual inspection of the engine oil pressure sending unit wiring harness and found evidence of engine oil on the wiring harness was present. Disconnected the engine oil pressure sending unit wiring harness connector, visually inspected the connector and terminals and found evidence of engine oil. Further inspection of the engine oil pressure sending unit showed sign of engine oil inside the engine oil pressure sending unit connector. Key on, used a fused jumper wire and tapped ground at the engine oil pressure sending unit sense circuit in the engine oil pressure sending unit harness connector and observed the engine oil pressure indicator changed, which indicated no circuit faults were present. Found the measured engine oil pressure was within the manufacturer’s specification. The results of these tests verified the engine oil pressure sending unit was faulty. There is also signs of oil leak from the oil cooler housing which the oil pressure sender mounts on too which will also need to be replaced.
    • REMOVE ALL NECESSARY COMPONENTS. REMOVE AND REPLACE INTAKE MANIFOLD, OIL COOLER HOUSING WITH THE OIL PRESSURE SENSOR, INTAKE MANIFOLD GASKET SET. ASSEMBLE TOGETHER AND MAKE ALL NECESSARY ADJUSTMENTS. ADD ENGINE OIL. TEST ALL AFFECTED AREAS.
     
    JASON L. gave our service a 5 star review on 6/15/2023

  • 2016 RAM ProMaster 1500

    RAM ProMaster 1500
    Mileage
    91,213
    Service Date
    2/15/2023
    Services Performed
    • MAKE SURE ALL WIRES ARE INSERTED INTO PROPER CAVITIES. RE-ASSEMBLE BACK TOGETHER. CONNECT BATTERY. MAKE SURE ALL OTHER WIRES ARE HARNESSED PROPERLY. TEST ALL AFFECTED SYSTEM.
    • HANDLING FEE
     
    JASON L. gave our service a 5 star review on 2/15/2023